The internet is not working. Self-configuring the Internet ufanet

- Andrey, how will this affect subscribers of the Ufanet cable network?

Absolutely nothing! Our subscribers now watch both analog cable television and digital on their TV, and everything will remain so. You will not need to buy any additional devices, change the TV. Everything will be good.

All the media are talking about this, exaggerating this topic. This causes concern among the citizens. How justified is this panic? Maybe you can explain what is actually going on?

Let's figure it out. Here, most likely, confusion has turned out. In Russia, there are three main types of television: cable television, which the company "Ufanet" provides, satellite, it is only digital. Not cable, not satellite, this question does not apply. And the so-called terrestrial television. This is the television that you can receive on your indoor antenna or on the collective antenna that stands on the roof of the house. The question concerns precisely terrestrial television, which is distributed through the air. There are two types: analog and digital. Digital has been relatively recently launched, it is a new direction in this area. But analog, it is very old and, in principle, it is natural that our legislators decided to stop supporting this television. And from 2019, as far as I know, it will be discontinued. That is, people who today watch analog terrestrial television using a room or collective antenna, yes, indeed, they will not see this television at some point. They will need to replace the TV with a modern one that accepts digital terrestrial television or purchase a digital set-top box for digital terrestrial television or connect to cable television, which is much easier.

Very often, against the background of misunderstanding of people, scammers are activated. How can unscrupulous people take advantage of this situation?

I heard such stories when some unscrupulous people start to frighten people who do not quite understand the topic: “buy expensive equipment, preferably directly from us, because analog TV will stop showing you tomorrow.” Once again, I would like to say that if you are connected to cable or satellite television and they are trying to tell you all this, that you urgently need to purchase something, most likely these are scammers. That is, in no case do not need to believe in it. And once again I want to remind you that this topic does not concern Ufanet cable television subscribers. No additional expenses, equipment purchases are required, so you can be calm.

How to set up an Internet connection yourself if your provider is Ufanet? This is very easy to do, just spend a few minutes carefully following the instructions below.

• Foreword
• Automatic connection creation
• Setting up a connection in Windows 10
• Setting up a Wi-Fi router to work with Ufanet

Slow Internet from Ufanet? Speed ​​sags in the evenings? And there's nothing to watch on TV?

Foreword

Currently, due to the ubiquity of Wi-Fi routers, subscribers connecting to the Ufanet Internet provider immediately buy or rent a wireless router through which the connection is made. If you have there is home wireless router, then immediately go to the appropriate paragraph of this manual. If not, and you connect the Internet cable directly to your PC or laptop, read on.

Automatic Connection Creation

Ufanet has released a utility that automatically creates a new connection in the system. You will only have to enter your data (login and password) that were given to you by the employees who connected you.

You can download it without creating a connection.

Plug the Ufanet cable into the network card connector, open a browser and enter the website address www.ufaman.ru (it will be available as a local resource)

• Support section
• section "Instructions"
• connection setup section
• select the version of the utility that matches your OS (Windows XP, 7, 8, 10)
• a window will appear where you will need to enter your data from the Ufanet service (login, password). A desktop shortcut will also be created for quick connection.

This completes the connection creation process.

Setting up a connection in Windows 7

You can set up a connection to Ufanet yourself in the Windows Vista or Windows 7 operating system in the following way:

Go to "Start" - "Control Panel". Open the "Network and Internet" menu

There we go to the "Network and Sharing Center" menu.

Select the menu command "Setting up a new connection".

From the list, select "Connect to the Internet" and click "Next".

The switch should be in the “No, create a new connection” position, click “Next” again

In the next window, select "High Speed ​​with PPPOE"

Enter the username and password from the Ufanet network. Check the boxes as shown and click "Create".

Click OK and try to connect.

Setting up a connection to Ufanet in Windows 10

Open Start - Settings

Network and Internet

Select "Dial" on the left. Then click "Set up a new connection"

"Internet connection"

High speed with PPPoE

Ufanet is a popular provider in the Republic of Bashkortostan, the company specializes in providing access to TV and the World Wide Web. Digital TV from Ufanet is the best combination of high-quality sound and video, thanks to which you can experience genuine emotions when watching the action on the screen. When connected to digital TV, users are completely immersed in their favorite shows and movies.

Interactive TV is available in every home

In order to set up channels for Ufanet correctly, it is important to know the procedure. The instructions below will help you set up Ufanet digital TV for Samsung devices.

detailed instructions

Of course, it all depends on the specific model, because the menu structure and interface may differ, but the procedure and essence do not change. You can set up your Samsung TV like this:

• press the Menu key on the remote control, this will help you go to the main menu of the TV;
• select "Country" in the "Channel" section;
• enter the standard pin code (1234, 1111, 0000) or the numbers that you set yourself;
• in the "Digital channel" parameter, you must select "Others". This will allow you to set up the TV correctly;
• click on "Cable Search Options" in the "Channel" section. Interestingly, in devices manufactured after 2010, this item may appear during the Auto-Tuning process.

Cable Search Options

At this point, we have to perform the most important settings on which the performance of television on Samsung technology depends. To tune in to the correct frequency, you should enter the end frequency 770000 and the start frequency 274000 of the city of Ufa. Set the modulation parameter to 256 QAM and the symbol rate to 6750.

After that, you can return to the “Channel” item and go to the “Auto tuning” menu. The type of channels (digital) is set there, as well as the signal source (cable).

If you did everything right, then when searching, the Samsung TV will find about 10 radio and about two hundred television programs.

Results

Ufanet digital television is configured in minutes on any TV. The procedure for different equipment is very similar, and consists of several elementary steps. Finally, we add that after searching for all TV channels, you can set the internal clock (GMT zone and "Auto" clock mode, this is done in the System - Time menu).

There is a provider in Ufa that provides communication via the PPPoE protocol. In other cities, the same provider provides communication through a different protocol - PPTP. We are talking about the company Ufanet.

It will not be difficult to connect a router to the Ufanet cable, and setting up a connection will be even easier. You just need to do everything in order, and the connection will work the first time.

Classic network combine Dir-300, its hardware ports

So, before setting up a connection with the Ufanet provider, you need to find out under which of the two protocols you will configure the router, under PPTP or PPPoE. In both cases, a username and password are used to establish a connection. Here we consider only the option of setting up a connection "PPTP". As for Ufanet, to create a connection with this provider, consider two nuances. Namely, it is necessary to disable IGMP in the connection settings interface, and it is better to specify “PPTP + Dynamic IP” as the protocol.

D-Link Router WAN Port Settings

We will show in an example what needs to be done to get into the web interface of the router. The experimental device was the Dir-300 router with a "black" interface, but by analogy, you can configure another model. And the common for all devices in which the PPTP connection method is implemented is the following. You can create a pair of connections (one under "Dynamic IP", the second under "PPTP"), or one single connection, the type of which is "PPTP + Dynamic IP".

It is important to know that those devices that use the protocol of the form "PPTP with a dynamic IP address" will work in the Ufanet provider's network. It is useless to set up a separate communication channel "IPoE" (dynamic IP) and a connection like "PPTP".

Go to the setup interface

After connecting a computer to any LAN port via a patch cord, do not immediately apply power to the router. Check that the network card is set to "auto" IP and DNS. You need to open the parameters of the TCP / IP v4 protocol:

Setting up a wired connection on a PC

But even if all the selectors were set correctly, right-click on the connection icon, and select the "Fix" line. Lastly, turn on the network harvester itself.

The device will boot up in about a minute. Then you open a browser and go to this address: 192.168.0.1. For non-D-Link devices, the address ends with "1.1". A form with an authorization request will appear in the browser window. For the model we are considering, the administrator login and password is the word “admin” without quotes. After successfully entering the interface, we advise you to switch the language to Russian.

What is displayed at the entrance

It is important to know that if it is impossible to go to the interface using standard methods, do the following. After loading the router, the reset button is pressed on it, holding it for 10-12 seconds. As a result, all settings will be reset (each of them will take the default value). Then, you can repeat the steps in this chapter - everything should work as it should.

Setting up a PPTP connection

We hope that the provider's cable is already connected to the WAN port of your router. If this is not the case, then know that you can connect when the device is completely de-energized. The following information must be written on the sheet:

• Ufanet network subscriber login;
• The value of his password;
• Domain name of the VPN server (it is always: pptp.ufanet.ru).

The digital address of the VPN server that is in use at the time of writing this review is 10.8.0.1. This value can be substituted for the domain name, but the provider does not recommend anyone to do this, be aware of this.

Actually, the interface of most home routers allows you to set an HTTP address, and not a set of numbers for an IP address. And you have to use it. By explicitly setting the VPN IP, we do not take into account the fact that the provider itself has the right to change the value of this IP at any time. And the network combine that we are configuring allows you to set the name (a sequence of letters of the HTTP address) in the string "VPN server".

Go to the WAN port settings tab

Open the GUI as discussed above. Switch it to the "Advanced Settings" mode, click on the "WAN" link.

Main web interface page

A tab will appear on which you need to click the "Add" button. A page with connection options should open.

Now we will set up a connection with Ufanet. You must perform the following steps.

Internet channel settings tab (beginning)

1. In the top list, select the value "PPTP + Dynamic IP";
2. Be sure to uncheck the "Enable IGMP" checkbox, you can do the same with the "Ping" option;
3. Scroll down the slider on the right side of the tab;
4. Fill in the fields with an asterisk: login, password, its confirmation, VPN server address;
5. We select the authentication algorithm "CHAP" (but you can leave "AUTO");
6. Uncheck the "Ping" box, click the "Save" button.

Internet channel settings tab (continued)

Finally, remember the changes you made. To do this, select "Save" from the top menu. and Restart”, and after rebooting the combine, it will connect to the provider automatically.

Some important tuning notes

The device that we configured contains the “correct” parameter values ​​by default. This will not always be the case, and it is important to know the following. The "Keep Alive" checkbox, which is contained in the settings tab, must be checked in any case. And for D-Link routers, this applies to two more options - "NAT" and "Firewall". Without them, the connection does not work at all, even regardless of the type of protocol.

But what happens if you use the "Ping" option (in other models it is called "WAN Ping Respond"). Just like a computer connected directly to an ISP, a router receives a specific IP address. From the outside network, ping requests can be sent to this address. We did not use this option so that our router would not respond to these requests.